Porter-Cable US58 1/4-Inch to 5/8-Inch 22-Gauge C-Crown Upholstery Stapler

Buy Cheap Porter-Cable US58 1/4-Inch to 5/8-Inch 22-Gauge C-Crown Upholstery Stapler

Buy Low Price From Here Now
The Porter-Cable US58 1/4-Inch to 5/8-Inch, 22-Gauge C-Crown Upholstery Stapler is an easy to use pneumatic stapler with plenty of useful features. It uses standard Senco C Type 22-gauge, 3/8-inch crown staples to get the job done right, and it includes a 1-inch nose extension for those tough to reach areas. The high-capacity bottom-load magazine handles 185 staples, and the driver guide moves back to easily clear jams from the magazine. The US58 stapler requires 70-120 PSI air pressure, so it will work with most air compressors.
Readmore

Technical Details

- High-capacity pneumatic upholstery stapler with 185 staple magazine
- Uses Senco C Type, 22-gauge, 3/8-inch staples from 1/4 to 5/8 inches long
- Quick and easy jam-clearing mechanism
- Measures six inches tall and nine inches long; weighs 2 pounds
- Includes a 1/4-inch air fitting with dust cover and oil
See more technical details

 "Porter-Cable Upholstery Stapler" 2010-07-23
By Jeffer
Lots of products out there to meet this need. Porter's unit is well built, feels solid, easy to operate, and a great entry price-point. I'm not a professional upholstery fabricator, I'm re-doing my boat upholstery and am using this unit with my Porter-Cable compressor, using 3/8" x 3/8" stainless steel staples and it's been great. And I'm confident that I could complete my job, and turn it around in near new condition on EBay and get 80-90% of my money back!



One hint, adjust the air on your gun and test staples. At the higher end of the range it'll set the staples so far that the fabric will pull out (depending on your material and base). I had to run it on the lowest setting in the recommended range, which was as low as my regulator would adjust.



I definitely recommend this unit. Also, great vendor as well!

 "This is a Pro Stapler for sure!" 2010-01-22
By W. Gravning
Like any well made product the Porter Cable Upholstery Stapler is absolutely a delight to use. The 1" long extension is a must for anyone working on upholstery projects. We used it recently on some oak chairs using 3/8" fine wire staples from Amazon at 70psi. Follow the instructions and you should have no problems.

 "Performed Flawlessly" 2010-01-17
By Rodney McQueen (Illinois, USA)
Have done various reupholstering projects through the years and had always hand stapled. What a difference this this tool made! It reduced the time required to complete the project and greatly improved the quality of the work. It did not "misfire" once. It is lightweight and easy to use. I highly recommend the tool, at least for home use.

 "excellent stapler" 2009-11-16
By yayamama (Western PA)
I bought this to replace one exactly like it that I have been using for 7 years. It broke because I FORGOT to oil it and the inside rusted....In conclusion take care of your tools and this is an excellent one.

 "WOW, great tool and Recommded" 2009-11-05
By Electric Z (Oregon)
Upon receiving this stapler I was using it within 10 minutes of the UPS delivery. It came with the air fitting already installed. I slapped some 1/2" staples in it and I was off working. It has a great ergonomic handle that feels great in your hand and is lightweight. My wife likes it too!



The stapler is of the high Porter-Cable expected quality. It made short work of my first project and expect many more hours of use. This tool is made for working. As fast you can pull the trigger the staples are set deep and no jamming. Recommended and the price was very reasonable.



Here it is a month later and wanted to add a couple thoughts since first purchase. First, it is working great and I am very happy.



Next, some have commented about a possible safety feature missing in that staples can be freely shot out, (no device needs to be pushed against the object being stapled first). After using it a lot, quite frankly I would find it a nuisance if there was such device. When working with fabric or some other material it would be a major impediment to have to reposition the stapler, push down and then pull the trigger. When stapling many staples with its current design you can just slide the stapler to the next position pull the trigger and move on. Much more efficient and faster.


Images Product

Buy Porter-Cable US58 1/4-Inch to 5/8-Inch 22-Gauge C-Crown Upholstery Stapler Now

Duracell Powersource Mobile 100

Buy Cheap Duracell Powersource Mobile 100

Buy Low Price From Here Now
The Duracell PowerSource Mobile 100 is a compact rechargeable source of portable power for AC and USB-powered devices. It will extend the runtime of mobile electronics such as an iPod, BlackBerry, video camera, cell phone, and can provide up to two hours of extended runtime for your laptop. The Duracell PowerSource Mobile 100 has one AC outlet and two USB charge ports, so you can run or charge multiple devices simultaneously. You no longer have to carry extra cords, chargers and device-specific batteries.
Readmore

Technical Details

- Combines a 100 Watt inverter with a lightweight, high-output lithium-ion battery pack
- 3-prong AC outlet charges or powers cell phone, IPod , BlackBerry or video camera
- Provides up to 2 hours of extended run time for laptop
- Temperature, overload and low-battery voltage shutdown protection
- Rechargeable from vehicle or home
See more technical details

 "Great product" 2010-05-14
By Michael Pascucci (Boston, MA USA)
Made the trip with me around Australia keeping my netbook, iphone, and camera battery charged on the go. I mainly used the AC jack, but occasionally hooked up the iphone directly to the USB port when I needed to charge my camera battery at the same time. Was able to charge my netbook from 0% to 100% twice on a single charge of the Duracell Powersource Mobile 100. It was key in my travels, as I spent 2 weeks camping in the outback - no hostels, hotels, or electrical outlets. I just had my Australian rental car with a cigarette lighter / 12v jack, and I had no troubles with using that to charge the Powersource Mobile. For reference, I also had a Duracell Power Inverter that did not work in the Australian car (although it possibly could have been damaged prior to that).



My only complaint is that the "charge remaining" indicator is not very helpful. The battery LED flashes orange while charging, and then again when low (beeps for about 5 seconds before it dies completely). It remains green when on. Otherwise, there is no way to gauge if you have, say, 90% left or 10% left. Likewise, do I need to leave it plugged in for 30 minutes or 4 hours to have any useful charge?

 "Don't buy from [...]!!!" 2010-04-29
By Scott Chou (San Francisco, CA United States)
The $30 price tag turned out to be too good to be true. The unit arrived unused, factory sealed but the manufacturing date was Oct 2006! These kinds of batteries don't have that kind of shelf life. The internal batteries are now dead and won't take a charge. I suppose [...] grabbed some kind of surplus inventory in order to offer this deal. Having said that, the product itself might have rated highly back in 2006. I'm sorry for dragging down its average rating here on the product page, but I see that [...] is the only supplier for this closeout special.

 "Convenient Portable AC Power Plug" 2010-04-17
By D. Sauer (Ohio)
I wish this sort of device was more common. When you travel around, finding an outlet can be a bit of a hassle. Just for fun I did some experiments using 13 watt compact fluorescent lights. On a single full charge, a 13 watt CFL will last well over an hour. 3 CFL's will last up to 20 minutes. My Cradlepoint CTR-350 will deliver a whopping 4 hours when plugged into this device. My Eee however will overload it and cause the device to shut down. To fully charge from AC, you can expect 2 to 4 hours. Keep in mind that while it functions as an inverter when plugged into a car's cigarette lighter, it will function as an inverter while slowly charging itself. When plugged into AC, it will not function as an inverter, and will not power any device.



I have only one major complaint: The unit is sealed, and that means the battery is not replaceable. Mine still holds a pretty good charge, but once the battery starts to break down, the unit becomes disposable.

 "Top 5 electronic purchases ever." 2010-04-08
By G. Weaver
I charged it. After the first use, I knew it would never be far from me. It works perfect. The life between recharges is great and even longer than listed.

 "Works as advertised" 2010-03-26
By Joe
I ordered three when they were on sale and I have no complaints. They do exactly what they are advertised to do. I noticed a lot of people complaining about the date of manufacture being very old and they had problems. All three of mine were manufactured on 03/April/2008 and they all perform flawlessly. Can power my wifi webcam (5 watts) for a solid 6 hours and change.

Have yet to try running one while feeding it 12v from a car, but I do want to experiment with these and a solar panel. Would open up a lot of interesting usage scenarios.


Images Product

Buy Duracell Powersource Mobile 100 Now

Power Line 0900-27 Global Power Travel Kit

Buy Cheap Power Line 0900-27 Global Power Travel Kit

Buy Low Price From Here Now
Global Power Travel Kit
Readmore

Technical Details

- Converts 220-Volt Electricity to 120-Volt power for use in locations world-wide
- Includes 5 adapters for different plug-in types around the world
- All plug-in types are enclosed in the global power adapter kit for ease of-Packing in the suit case
- For use with electrical appliances requiring up to 1600-Watt and electronic devices up to 50-Watt
- Converts foreign-Voltages for safe operation of your personal appliances and electronics while abroad
See more technical details

 "Travel converter" 2010-04-18
By Whizzin' (California, USA)
Have not had the opportunity to use this yet as I have not travelled to an international location, but it appears to be exactly what I am anticipating needing in the future.

 "Great, but not perfect" 2010-03-12
By Tim Little First Church
The product worked as advertised. I am indeed glad that it has a fuse in case of short or overload. Given that its intended use is in a foreign country, in my case India, it would have been awfully nice to have had a replacement fuse included in the carrying case. For half the trip, I had a wonderful power converter which had not been blown up in an unfortunate short because of a fuse; but no way to purchase or find a replacement fuse in a foreign and somewhat remote area. For those planning to purchase this unit, it travels well and the plugs work great for the growing number of items which are already set up for 220 volts (most newer Apple products can automatically switch if plugged into different current.) The 50 watt setting is fairly useless. The unit got hot to the point of melting even charging a phone on the 50 watt setting. The 1500 watt setting worked very well. And pick up a couple of small 5 amp automotive fuses to stick in the carrying case. For less than a dollar you can keep running in the event of an unfortunate short or voltage spike.

 "Design Issues" 2010-01-07
By T. Shah
We purchased this product prior to a trip to Europe and parts of North Africa. We thought that it would be very useful for our electronics. We actually had to buy this product a second time because the voltage converter blew out (and the plastic around it melted slightly) as a result of my wife's hair flattener, though I'm not sure she read the wattage on it before using the voltage converter. Here's what we've found:



Pros

- Cheap

- Easy to use because the instructions seem somewhat dumby proof - using color coding and symbols. This isn't our first time traveling overseas, so we didn't need it.

- The adapters work without issue. They're great. You don't really need to color coding since it's really just about plugging into the outlet whatever fits best.



Cons

- As I mentioned earlier, the voltage converter burned out on us. In general it gets quite hot

- Design issue for wall outlets. The convertor adds to a adapter, which means it all gets heavy, so the whole thing curves downward or can easily fall out if the outlet is old or loose. We worked around this by finding a way to plug it into the floor or table in our hotel



We bought this product a second time just to get the the convertor, so it wasn't bad. It was relatively cheaper to do that than buy something else.

 "STAY AWAY FROM THIS!" 2009-12-28
By D.S. (Milwaukee, WI)
I bought 4 different kind of voltage converters for my India trip and this was one of them specifically to plug in electronic equipments at lower wattage 50 Watt setting. I plugged in my Graco baby monitor adapter into this converter. It worked for 8 hours and then damaged my Graco adapter. Later I figured out why it damaged it. The converter gets extremely HOT! Thus it heated up the Graco adapter and eventually damaged it. I should have used an extention cord between the converter and adapter.



This product is terrible. There are better (and affordable) converters that do not heat up as much. For example, the 50 Watt converter made by Seven Star Model SS212 works great. I bought this from world gift center for only seven dollars. I use this for my wireless router 24/7 and it has not caused any problems so far. It does not heat up at all. I wish I had bought more of these.



The SMF-200 step down converter is also good but it does heat up a little bit. The good thing is that it provides 200 Watts for electronic equipments. I use this for my Sonicare tooth brush and Graco monitor receiver.

 "50 - 1600 watt Converter/Adaptor" 2009-11-18
By C. Hill (minnesota)
It worked fine for charging our phones and curling iron but could not get it to work for AA battery recharger for my camera. Not sure what I did wrong. I liked the very sturdy plastic box which kept everything in it's place.


Images Product

Buy Power Line 0900-27 Global Power Travel Kit Now

Dremel Attachments & Accessories Collection

Buy Cheap Dremel Attachments & Accessories Collection

Buy Low Price From Here Now

Readmore

Technical Details

See more technical details

Images Product

Buy Dremel Attachments & Accessories Collection Now

SE Pick Set, 12Pc

Buy Cheap SE Pick Set, 12Pc

Buy Low Price From Here Now
Pick Set, 12Pc
Readmore

Technical Details

- A new set of 12 stainless steel wax carvers
- Stainless steel construction & can be autoclaved
- Well made and long lasting
- Great for technicians,hobbists for fly tying,beading,hobbies and many other household uses.
- Made In China
See more technical details

 "Great" 2009-12-03
By Maria
I'm really happy with these picks. They're great for polymer clay, plasticene, and wax. There's plenty of variety in the shapes. There're pretty sturdy, and the picks that are supposed to be sharp are definately sharp enough. Overall, great product for the price.

 "A nice tool set" 2009-06-17
By Juan Luis Fuste Martinez (Barcelona, Spain)
A nice tool set to any Sculpey fan. I use for modelling, no other uses. Fast delivery!!!

 "Has many tools but not all are good for clay modeling" 2009-02-27
By H. Oh (Norwalk, CA USA)
Has many tools but not all are good for clay modeling and I used only few out of the whole set.


Images Product

Buy SE Pick Set, 12Pc Now

Milwaukee 48-59-2818 18-Volt to 28-Volt Lithium-Ion and NiCad Slide Style 1-Hour Battery Charger

Buy Cheap Milwaukee 48-59-2818 18-Volt to 28-Volt Lithium-Ion and NiCad Slide Style 1-Hour Battery Charger

Buy Low Price From Here Now
The Milwaukee 18-to-28-Volt Universal Battery Charger charges both Li-Ion and Ni-Cad batteries from 18-to-28-volts. This universal charger makes the transition from Ni-Cad to newer Li-Ion batteries seamless by providing single charger simplicity. The charger will charge Li-ion batteries in 1-hour and Ni-Cad batteries in 40-minutes. Ni-Cad packs will charge 20-minutes faster on this charger than the current Milwaukee Ni-Cad-only chargers. The charger also features a top-off conditioning mode that automatically conditions 18-volt Ni-Cad battery cells for extended battery life. Automatic temperature monitoring continually monitors the battery's temperature and deliverers the appropriate current for that temperature. Progressive charge indication battery LEDs light up incrementally as the battery is charged. This feature provides a quick indication of remaining charge time or if the pack is charged enough for the job at hand. A pass-through plug conserves valuable outlet space and rubberized feet keeps the charger in place.
Readmore

Technical Details

- Versatile and reliable 18-to-28-volt universal battery charger
- Charges both Li-Ion and Ni-Cad batteries from 18- to 28-volts
- Top-off conditioning mode automatically conditions 18-volt Ni-Cad battery cells to extend run-time and life
- Automatic temperature monitoring delivers the correct charge current for that temperature
- Pass-through plug conserves outlet real estate
See more technical details

 "Milwaukee NiCad drawing" 2010-03-02
By Brad Chapman
The item was delivered promptly and was exactly what I ordered at a very competitive price.

 "Improved battery charger" 2010-02-15
By Joseph Bobst (Central Illinois)
Perfect for the transition to Li-ion power. As my collection of tired NiCd's dies, I can postpone another new Li-ion for a while by keeping the old timers charged. Meanwhile, the NiCd's seem, subjectively, to be doing a bit better.

 "Satisfaction" 2010-02-08
By Luis L. Delrosario (San Diego,CA USA)
Im a satisfied customer and your product really works fine. Got no complain about that.I can recommend to use Amazon.com to anybody.

 "Great, restored a previously useless battery" 2010-02-01
By W. Sweasy (Red Wing)
I had an older battery that didn't charge on my old charger. I bought this charger when I bought a lithium battery. I tried the dead battery and it brought it back to life.

 "Great Charger so far" 2010-01-24
By The Big L (DC)
So far this charger has worked just fine. We'll see how things bear out over the long run though.


Images Product

Buy Milwaukee 48-59-2818 18-Volt to 28-Volt Lithium-Ion and NiCad Slide Style 1-Hour Battery Charger Now

DEWALT DW9116 7.2-Volt to 18-Volt Pod Style 1 Hour Battery Charger

Buy Cheap DEWALT DW9116 7.2-Volt to 18-Volt Pod Style 1 Hour Battery Charger

Buy Low Price From Here Now
Volts: 7.2 - 18, Battery Charging Time (hrs.): 1, Compatible With: DeWalt Batteries, LED Indicators: Yes, Thermal Protector: Yes, Automatic Tune-Up: Yes
Readmore

Technical Details

See more technical details

 "just recieved very prompt delivery" 2010-03-07
By W. T. peace (San Francisco, CA)
too early for quality review but the service was very fast the item works very well so far, smooth transaction

 "GREAT PRODUCT-QUICK ORDER DELIVERY" 2010-02-17
By Larry Crater (Winston Salem NC USA)
Was amazed at how this charger restored my 14.4v FIRESTORM batteries. They seem stronger and last much longer than with original B/D charger that had failed after limited use. Amazon price was less than half of local home improvemnt store price. No user instructions came with product but I downloaded free user guide from DEWALT web site. Also recieved product in 2 business days after order was placed. GREAT PRODUCT, GREAT SERVICE!!!

 "dewalt charger" 2010-02-14
By Kris M.
My black and decker cordless battery charger stopped working. I was going to replace it with the same until I read a review. It basically stated that the B&D battery charger would die when a bad battery was placed for recharging. Reading further I found mention of the dewalt charger, same maker as B&D, and it would indicate a bad battery (rather than cease to function). So I felt I was making a very good purchase based on this information. Well, I wasn't wrong. As soon as I recieved it, I put it to work. The battery was charged in less than an hour. I feel it was well worth the purchase price as I had two batteries and the older one was failing. Had I gone with the black and decker, without a battery check, the charger would have died and I would have tossed everything,the drill,the batteries and the charger. I feel I made the best purchase for my situation,and saved a bundle. And, I'm glad I read the reviews before making my purchase.

 "DeWalt DW9116 Charger" 2010-01-31
By Kenneth R. Bigbee
The DwWalt DW9116 charger arrived withing 3-5 days after ordering. The charger worked flawlistly and recharged two batteries which would not charge using the original charger.

 "Worth the price" 2010-01-17
By P. Vang (St. Paul, MN USA)
Lent my DeWalt to my brother who lost the charger. Went to **** and they wanted to charge $110 at the store. Searched Amazon and found this one. Looks, feels, and does the same thing, and in fact, brother can't even tell that it's a new charger.



This is just the charger though. Nothing else, including the instruction, comes with it.


Images Product

Buy DEWALT DW9116 7.2-Volt to 18-Volt Pod Style 1 Hour Battery Charger Now

HK1 Hydrokinetic Adjustable Wrench

Buy Cheap HK1 Hydrokinetic Adjustable Wrench

Buy Low Price From Here Now
This is the World's first hydrokinetic adjustable wrench and is the only box-end wrench you need. It is as slim, reachable and strong as regular wrenches but you only need to carry one. It got very high evaluation by 'Popular Science' and 'Tool Snob'.

"The HK1 Hydrokinetic Wrench is one of the more innovative items we've come across in quite a while." - by Tool Snob

"One of the 12 must have products of 2009" - by Popular Science Magazine
Readmore

Technical Details

- 7.5 inches, Nickel plated cold forged steel
- Unique Hydrokinetic adjustment system
- Easily adjusts to cover 23 sizes, metric and standard
- Slim and ergonomic design allow to fit into hard to reach areas
- Strong grip to remove damaged bolts and nuts
See more technical details

 "OK, not as good as a std crescent wrench" 2010-02-19
By D. C. Clark (Fairfax, VA USA)
See other reviews - this wrench is too hard to adjust. Takes at least two, maybe three hands to hold everything, adjust, and lock. If it were redesigned to allow a thumb adjust and a finger lock, it would be a winner.



Also, remember that this is a box-end style wrench. Not every bolt or nut can be loosened with it. You'll still need a good old crescent style wrench in the toolbag. So then, you may well ask why you need it...

 "Neat Design, but not as neat funcionally" 2010-02-14
By Dave - Free as Can Be (Franklin, TN)
This wrench is a new angle of an ajustible wrench that has been around for years. The HK1 is designed to fit a nut or bolt by sliding a center piece of the wrench within the formed 3 sided body of the fixed wrench side to add a fourth side that pushes tight against the open side of the wrench. In other words, this wrench will tightly grip a normal six sided bolt or nut by at least 4 sides making a tight fit to tighten or loosen a bolt or nut. I ordered one of these because it looked neat and appeared to be a modern solution to tightening or loosening a bolt/nut. This wrench is not as convienient or as fuctional as a normal adjustible wrench. And, because the sliding action within the wrench that makes up the fourth side is quite stiff, I rate this wrench with 2 stars because it is not as functional as the regular Craftsman or Crescent adjustable wrench. If the sliding part of the wrench worked more smoothly and lightly, I would rate it 1 star higher. Sometimes I get suckered into believing a new design would be superior to the old. This is one of those times. It is just a neat looking idea that does not serve its purpose as well as the simple and cheaper adjustable wrenches on the market. Even though it does not work well in practice, it is still a neat looking tool.

 "OK for emergencies" 2010-02-13
By William Ayres (Albuquerque, NM USA)
This wrench seems to work OK but is a little hare to adjust. There is an opening at each end, one for larger nuts and one for smaller. You have to stick your finger into the one you are not using and slide the center bar into place by pushing it. It would be difficult for someone with big hands. I wouldn't buy another one

 "handy dandy tool" 2010-02-12
By skmsmith (Clio, MI USA)
I got this tool for my adult sons for Christmas. THEY Love IT!!! Would recomend to anyone as it was economical also.thx

 "Nifty gadget, little tricky to use" 2010-01-09
By B. Farnsworth (Cleveland, OH United States)
A little tricky to adjust, the locking knob is small and is somewhat difficult to manipulate. Also, you may have trouble moving the post if you have very large fingers. But an interesting tool anyway.


Images Product

Buy HK1 Hydrokinetic Adjustable Wrench Now